X729-script

Overview

[NOTE]: X729 don't support Raspberry Pi 5 hardware

This is script installation tutorial for X729 shield, it will replace X729 Software installation tutorial, although X729 Software installation tutorial is still available, but we strongly recommend that you use this script tutorial, which simplifies the installation process and reduces dependencies on third-party python libraries.

Now we think you have successfully flashed the OS Image into Micro SD and and power on the device, and you have also completed the operations such as creating new user required in some OS. You need to perform the following operations in Terminal.

[NOTE]:

1. The script now supports the Raspberry Pi OS BOOKWORM version. You just need to uninstall the original script and reinstall it. Please refer to the following:

OPen ternimal window, then run the following command:

mv x729-script x729-script-old
git clone https://github.com/geekworm-com/x729-script
cd x729-script
chmod +x *.sh
./uninstall.sh

Then just follow the installation process below.

2. Fix fan not working on Raspberry Pi 5 hardware

If you are using it on a Raspberry Pi 5, make the following changes:

1. Be sure to update the kernel to version 6.6.22.

sudo apt update
sudo apt full-upgrade
sudo rpi-update

2. Change the PWM_CHIP_PATH to /sys/class/pwm/pwmchip2 on line 7 of x729fan.sh

OS that has been tested

Raspbian
DietPi
Manjaro
Ubuntu
myNode
Umbrel
Volumio
RetroPie
Twister

Install

Please follow the steps below:

Enable I2C

Reter to How to enable I2C

NOTE: sample/bat.py will run with error if you don't enable I2C.

Check & review I2C address:

pi@raspberrypi:~ $ sudo i2cdetect -y 1
     0  1  2  3  4  5  6  7  8  9  a  b  c  d  e  f
00:          -- -- -- -- -- -- -- -- -- -- -- -- -- 
10: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
20: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
30: -- -- -- -- -- -- 36 -- -- -- -- -- 3c -- -- -- 
40: 40 -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
50: -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- -- 
60: -- -- -- -- -- -- -- -- 68 -- -- -- -- -- -- -- 
70: -- -- -- -- -- -- -- --

Explaination:

#36 - the address of the battery fuel gauging chip
#3c - address of oled display，This value only exists when the oled is inserted，check if the OLED is inserted in the correct direction if you don't found the above i2c port
#40 - TI INA219 12-bit current/voltage/power monitor
#68 - the address of the RTC chip

Preconfigured `config.txt`

To install pwm fan, first add dtoverlay=pwm-2chan,pin2=13,func2=4 to /boot/firmware/config.txt under [all] or the end of file and reboot:

sudo nano /boot/firmware/config.txt

Save & exit.

sudo reboot

Clone the script

git clone https://github.com/geekworm-com/x729-script

cd x729-script
chmod +x *.sh

PS: For some OS such as Raspberry Pi OS Lite, the git tool is not installed by default, if you get an error like error: -bash: git: command not found, please run the following command to install the git tool.

sudo apt install -y git

Create the x729-fan service

x729-fan service is for pwm fan, the pwm fan will automatically adjust the runing speed according to the temperature of the cpu after the service is started.

sudo cp -f ./x729-fan.sh                /usr/local/bin/
sudo cp -f ./x729-fan.service           /lib/systemd/system
sudo systemctl daemon-reload
sudo systemctl enable x729-fan
sudo systemctl start x729-fan

Then the pwm fan starts running.

Create the x729-pwr service

x729-pwr service will be responsible for power management and hardware safe shutdown.

sudo cp -f ./x729-pwr.sh                /usr/local/bin/
sudo cp -f x729-pwr.service             /lib/systemd/system
sudo systemctl daemon-reload
sudo systemctl enable x729-pwr
sudo systemctl start x729-pwr

Now, if you press and hold the onboard switch for 3 seconds, then the blue LED will flash slowly and the shutdown is going then all LEDs will be off until the device is completely powered off.

Prepair software shutdown script

sudo cp -f ./x729-softsd.sh             /usr/local/bin/

Create a alias x729off command to execute the software shutdown

echo "alias x729off='sudo /usr/local/bin/x729-softsd.sh'" >>   ~/.bashrc
source ~/.bashrc

Then you can run x729off to execute software shutdown as follows

x729off

Uninstall

./uninstall.sh

Test safe shutdown

Software safe shutdown command:

x729off

DON'T run the 'shutdown' linux command to shut down, otherwise the power of x729 shield will not be shut down.

Hardware safe shutdown operation:

You can verify the safety switch through the onboard switch, press and hold the switch for 3 seconds, then the blue LED will flash slowly and the shutdown is going then all LEDs will be off until the device is completely powered off.

press on-board button switch 1-2 seconds to reboot
press button switch 3 seconds to safe shutdown,
press 7-8 seconds to force shutdown.

Sample Files

The example programs are only suitable for advanced players, and you can construct your own usage scenarios according to the example programs.

Each example program demonstrates a different function:

read_fan_speed.py: Read the pwm fan running speed;

cd ~x729-script
sudo python3 sample/read_fan_speed.py

pld.py: AC Power supply loss dection script;

cd ~x729-script
sudo python3 sample/pld.py.py

plsd.py: Auto shutdown when AC power loss or power adapter failure script;(Added auto shuntdown function base pld.py)

cd ~x729-script
sudo python3 sample/plsd.py

buzzer.py: demonstrates how the buzzer will sound when power supply is lost, which is very important in some usage scenarios.

cd ~x729-script
sudo python3 sample/buzzer.py

PS:

1. The above sample python file maybe depends on the third-party python library `Rpi.GPIO`. In the official Raspberry Pi OS and most third-party OS, this library is installed by default. If you run this file and get some errors, try to run the following command to install the Rpi.GPIOy library.

sudo apt-get install -y python3-smbus python3-rpi.gpio

Or you can refer to How to Install RPi.GPIO Python Library

2. The sample program is only to demonstrate how to use the advanced functions of the shield, we do not provide the development function of the sample program.

Enable OLED display

Refer to How to enable OLED display

Set and Read the RTC time

Refer to How to enable RTC

Other

pwm_fan_control.py is no longer used, and are reserved here for research and use by python lovers only.

Support

Email: support@geekworm.com

FAQ

Q: How to login volumio via SSH?

1. Enable SSH:

Visit http://volumio.local/dev/, then click ENABLE SSH button

2. URL connection is IP address, and the default user name is volumio, default password is volumio

Q: How to login to Umbrel via SSH?

A: ssh umbrel@umbrel.local (or ssh umbrel@). the default user name is umbrel, default password is moneyprintergobrrr

Q: How to login to myNode via SSH?

A: URL connection is IP address, and the default user name is admin, default password is bolt

Q: How to login to DietPi via SSH?

A: URL connection is IP address, and the default user name is root, default password is dietpi

Q: Is LibreELEC supported?

A: TODO

Other resource

Chip-Specifications：File:MAX17040-MAX17041.pdf
I2C address: 0x36 for battery fuel gauging, 0x68 for RTC
References: Raspberry Pi Tutorial: How to Use a Buzzer

Return to X729 or X729-hardware

Enable comment auto-refresher

X729-script

Contents

Overview

OS that has been tested

Install

Enable I2C

Preconfigured `config.txt`

Clone the script

Create the x729-fan service

Create the x729-pwr service

Prepair software shutdown script

Uninstall

Test safe shutdown

Sample Files

Enable OLED display

Set and Read the RTC time

Other

Support

FAQ

Other resource

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

Tools

In other languages

WIKI

X729-script

Contents

Overview

OS that has been tested

Install

Enable I2C

Preconfigured config.txt

Clone the script

Create the x729-fan service

Create the x729-pwr service

Prepair software shutdown script

Uninstall

Test safe shutdown

Sample Files

Enable OLED display

Set and Read the RTC time

Other

Support

FAQ

Other resource

Navigation menu

Search

Preconfigured `config.txt`