Related changes

Enter a page name to see changes on pages linked to or from that page. (To see members of a category, enter Category:Name of category). Changes to pages on your Watchlist are in bold.

Recent changes options Show last 50 | 100 | 250 | 500 changes in last 1 | 3 | 7 | 14 | 30 days
Hide registered users | Hide anonymous users | Hide my edits | Show bots | Hide minor edits
Show new changes starting from 18:54, 23 April 2024

List of abbreviations:

N: This edit created a new page (also see list of new pages)
m: This is a minor edit
b: This edit was performed by a bot
(±123): The page size changed by this number of bytes

23 April 2024

			11:48		(Comments log)‎[136.23.0.128‎; 47.181.223.243‎; Lisa‎ (4×)]
					11:48 Lisa talk contribs posted a new comment on P511 ‎(Hi,the screw size: M2.5 x 9.5; Note: the screw of P511-A's Fan :M2 x 10)
					11:40 Lisa talk contribs posted a new comment on XScript ‎(Hi，Yes, if you do not install the script, press 7-8 seconds to force shutdown.)
					10:55 Lisa talk contribs posted a new comment on X-UPS1 ‎(Hello,you can use the output of one of the UPS boards)
					10:46 Lisa talk contribs posted a new comment on X1001 ‎(Hello，It doesn't support disable the LED light, you can cover it with something)
					04:54 47.181.223.243 talk posted a new comment on X650 ‎(Resolved. Board v.1.5 is still using pcf8563 not ds1307 so no change in config.txt is necessary.)
					02:47 136.23.0.128 talk posted a new comment on X1011 ‎(I would also like a case produced. Thanks) Tags: Mobile web edit, Mobile edit

11:02

X735-script‎ diffhist +82‎ Harry talk contribs →‎FAQ

10:08

X735‎ diffhist +97‎ Cindy talk contribs →‎FAQ

22 April 2024

			15:48		(Comments log)‎[90.77.46.17‎; 177.99.103.158‎; 108.76.201.4‎ (2×)]
					15:48 90.77.46.17 talk posted a new comment on XScript ‎(If I do not install the script, I can still switch on and switch off my Pi4 with the X-C1 board. Is that save or is it like a hard shut off which might corrupt my SD card?)
					05:33 108.76.201.4 talk posted a new comment on X1001 ‎(I posted as anon user #15 earlier. I think I got the problem resolved by routing the cable a little differently. I noticed I did not have the problem if the device was outside of the case (Geekworm P579-V2-K). I tried adding some electrical tape to the inside of the case (per Q4), but that didn't make a difference. However, I noticed that, when the pi was installed in the case, the FCC cable was being pressed against the inside of case, which caused it to bend some and appeared to cause...)
					04:04 177.99.103.158 talk posted a new comment on X1001 ‎(Is there a way to disable the LED light, its so annoying.)
					01:14 108.76.201.4 talk posted a new comment on X1001 ‎(I've installed the X1001 with a 128GB Silicon Power P24A60 (Model A60), and it has booted and ran fine for at least an hour or so, then everything just stops responding and basic commands like sudo and ls are no longer found. It behaves as though the drive has being disconnected, but the blue light is still on when this happens. I have re-seated the FCC cable on both ends a few times. It seems to be seated fully and securely. Also, the drive is typically recognized (at least momentarily)...)

13:13

How to update eeprom firmware‎ diffhist 0‎ Harry talk contribs

21 April 2024

09:39

Comments log 212.102.44.164 talk posted a new comment on X-UPS1 ‎(When multiple boards are stacked can I use the outputs on all boards, or only the first? Thanks!)

20 April 2024

			05:22		(Comments log)‎[64.77.248.35‎; 47.181.223.243‎ (2×)]
					05:22 47.181.223.243 talk posted a new comment on X650 ‎(additional error: "dmesg \| grep rtc [ 8.242339] rtc-ds1307: probe of 1-0068 failed with error -5")
					04:05 64.77.248.35 talk posted a new comment on P511 ‎(What is the screw size if I want to get replacements)
					02:25 47.181.223.243 talk posted a new comment on X650 ‎(even after replacing with dtoverlay=i2c-rtc,ds1307 I'm getting error: No usable clock interface found. hwclock: Cannot access the Hardware Clock via any known method. and there is no /dev/rtc or /dev/rtc0)