Changes

# Firstly'''Only''' Raspberry Pi OS ('''Bookworm''') supports PCIe, you can read [Raspberry Pi OS bullseye is NOT supported, refer to https://geekwormwww.raspberrypi.com/communitysoftware/operating-systems/# Make sure that your OS configuration (<code>/boot/forumfirmware/topicconfig.txt</120764code>) is completely correct: refer to the tutorial:[[NVMe SSD boot with the Raspberry Pi 5]] (will Continuously updating)# <span class="tb_red">Update the bootloader firmware to the last verson, refer to [[How to update eeprom firmware]], this is very important!!!</geekwormspan> Make sure your upgrade is successful by running command '''vcgencmd bootloader_version'''# Add '''''PCIE_PROBE=1''''' to the eeprom, (Run '''sudo rpi-x1001eeprom-forconfig -raspberry-pi-5 edit''' command, then add this post] line, then press CTRL+O to write change to file, press CTRL+X to get some help;exit, then '''reboot''')# Make sure the SSD type you use is correct, only support <span class="tb_red">M.2 NVME (Sata) Key-M SSD '''</span>NOT support''' M.2 NGFF Key-B SSD. Refer to the following right diagram (click it to zoom out): [[File:Supported-SSD-1.jpg|100px]]# Check if Make sure the FFC FPC cable is '''firmly and fully inserted''' into the PI 5, this is '''very important'''. Is For [[X1003]] shield, make sure the HAT tightly connected? We recommend you to send us the FFC connection schematic as well.# FPC cable '''Onlydirection''' Raspberry Pi OS (is correct also.# <span class="tb_red_bold">For [[X1003]] shield, make sure the FPC cable '''Bookwormdirection''') supports PCIe, Raspberry Pi OS bullseye is NOT supportedcorrect also. If an error still occurs, refer replace the FFC cable to test or purchase other PFC from here<ref><br/>Amazon US: https://www.raspberrypiamazon.com/dp/B0CXCTPQ2N<br/>Amazon DE: https://www.amazon.de/dp/B0CX4T993J<br/>Amazon UK: https://www.amazon.co.uk/dp/B0CX4T993J<br/>Amazon JP: https://www.amazon.co.jp/dp/B0CYGKN7G1</ref>to troubleshoot the issue.<span># Read [https://geekworm.com/softwarecommunity/forum/topic/120764/operatinggeekworm-x1001-for-raspberry-pi-systems/5 this post] to get some help;# Although you can also boot from a SD card, Pi OS is required for the NVMe SSD to boot, DON'T forget Flash OS onto into NVMe SSD.

<!--# Add If your SSD is old and has a '''DOS partition'''PCIE_PROBE=1, delete the DOS partition and repartition the SSD (feedback from buyer)--># Start thinking about SSD compatibility issues and try to switch to other brands of NVME SSDs.# Contact us at email: support@geekworm.com, and attached your product model, OS version (run '''uname -a''' to the eepromget), bootloader version (Run run '''sudo rpi-eeprom-config --editvcgencmd bootloader_version''' command, then add this line, then press CTRL+O to write change get) and order number :*'''How to file, press CTRL+X to exit, then reboot)get FPC Wires:'''<references /># ::<span class="tb_red">Update PS: The shortest length of the bootloader firmware to the last verson, refer to [[How to update eeprom firmware]], this FPC cable here is very important!!!</span>And finally be sure to run the command ''vcgencmd bootloader_version'30mm''' to check if your upgrade was successful!# For [[X1003]], if an error occurs, replace but the length of the FFC FPC cable to test.# If your SSD used by X1003 is old and has a only '''DOS partition22mm'''. For X1003, delete this may not be perfect, but you can use these FPC cables to troubleshoot the DOS partition and repartition the SSD (feedback from buyer)# Contact us at email: support@geekwormissue. DON'T buy it if you mind.com</span>

QQ3: How to fix the 2230/2242/2260 SSD on X1001 or other PIP?

QQ4. X1002 can't boot when install into the P580 case?

QQ5: Which NVMe drives work with a Raspberry Pi 5?